In this section:

Prerequisites

Compiler

C/C++test DTP Engine must be configured for use with specific C and C++ compilers and versions before you can analyze code. The configuration should reflect the original compiler and version used for building the code under test. The original compiler executable must be available on $PATH (unless it is specified with a full path). 

Use the -compiler switch to specify the compiler configuration identifier:

cpptestcli -config "builtin://Recommended Rules" -compiler gcc_4_5 -input cpptest.bdf

Alternatively, you can configure the cpptest.compiler.family property in a custom configuration file:

cpptest.compiler.family=gcc_4_5	

If you are using a single compiler and version for all testing, the compiler identifier can be specified in the cpptestcli.properties global configuration file in either the [INSTALL_DIR] or [USER_HOME] directory; see Configuration Overview.

Compiler Discovery

Perform one of the following actions to find the configuration for your compiler:

• Use the -detect-compiler switch to the auto-detect configuration:

  cpptestcli -detect-compiler gcc

• Use the -list-compilers switch to find the configuration in the list of all supported compilers:

  cpptestcli -list-compilers

See Configuring the Compiler and Supported Compilers for additional information.

About Usage Examples

The following instructions assume that:

• GNU GCC 3.4 compiler is being used (configuration identifier: gcc_3_4)
• The prerequisites discussed above have been met.
• Users are running commands in the [INSTALL_DIR]/examples/ATM directory.

Analyzing a Single File

Run an analysis and specify the original compiler command with the -- switch (separator).

cpptestcli -config "builtin://Recommended Rules" -compiler gcc_3_4 -- gcc -I include Bank.cxx

C/C++test will analyze the Bank.cxx file using the original compiler executable and compiler options and report detected violations to the output console.

Only the specified source files will be analyzed. Header files included by the source files will be excluded from analysis. To broaden the scope of files tested, including header files, see Configuring the Test Scope.

Analyzing a Makefile-based Project

Run code analysis and specify the original build command with the -trace switch.

cpptestcli -config "builtin://Recommended Rules" -compiler gcc_3_4 -trace make clean all

C/C++test will perform the following tasks:

1. Run the original build (make clean all)
2. Detect which files to test
3. Run the analysis for these files
4. Report results to the output console
5. Store all build information in the cpptest.bdffile for future runs (see About Build Data Files for additional information about build data files).

C/C++test will detect a source file for testing only if that file was compiled when running the build command. Only source files from Makefile will be analyzed. Header files included by the source files will be excluded from analysis. To broaden the scope of files tested, including header files, see Configuring the Test Scope.

About Build Data Files

You can create a build data file (.bdf), which stores information such as the working directory, command line options for the compilation,and link processes of the original build, so that C/C++test can analyze a project without having to rebuild it. The following example is a fragment from a build data file:

working_dir=/home/place/project/hypnos/pscom
project_name=pscom
arg=g++
arg=-c
arg=src/io/Path.cc
arg=-Iinclude
arg=-I.
arg=-o
arg=/home/place/project/hypnos/product/pscom/shared/io/Path.o

You can use the -trace switch to create a .bdf or use the standalone cpptestscan or cpptesttrace utility located in the [INSTALL_DIR]/bin directory.

Using cpptestscan and cpptesttrace Utilities

The cpptestscan utility is used as a wrapper for the compiler and/or linker during the normal build. To use cpptestscan with an existing build, prefix the compiler/linker executable with cpptestscan when building the code base. This can be done in two ways:

• Modify the build command line to use cpptestscan as the wrapper for the compiler/linker executables
• If you aren’t able to override the compiler variable on the command line, embedcpptestscan in the actual make file or build script.

To use cpptesttrace with an existing build, prefix the entire build command with cpptesttrace when building the code base. cpptesttrace will trace the compiler and linker processes executed during the build and store them in the build data file.

In both cases, you must specify the full path to either utility in your PATH environment variable. Additional options for cpptestscan and cpptesttrace are summarized in the following table. Options can be set directly for the cpptestscan command or via environment variables. Most options can be applied to cpptestscan or cpptesttrace by changing the prefix in the command line.

Basiccpptestscanusage:

• Windows: cpptestscan.exe [options] [compile/link command]
• Linux and Solaris: cpptestscan [options] [compile/link command]

Basiccpptesttraceusage:

• Windows: cpptesttrace.exe [options] [build command]
• Linux, Solaris: cpptesttrace [options] [build command]

Re-analyzing a Project without Re-building

Run code analysis and specify the existing build data file with the -input switch:

cpptestcli -config "builtin://Recommended Rules" -compiler gcc_3_4 -input cpptest.bdf

C/C++test will perform the following tasks:

1. Read the information about which files to test from the existingcpptest.bdffile
2. Run the analysis for these files
3. Report results to the output console
4. The original build will not be executed

Multiple build data files can be specified using multiple -input switches:

cpptestcli -config "builtin://Recommended Rules" -compiler gcc_3_4 -input project1.bdf -input project2.bdf

Only the source files defined in the build data file will be analyzed. Header files included by the source files will be excluded from analysis. To broaden the scope of files tested, including header files, see Configuring the Test Scope.

Testing a Microsoft Visual Studio Project or Solution

C/C++test can read Visual Studio project and solution files and analyze all source and included header files from the project or solution. Use the -input switch to specify a Visual Studio project or solution file:

cpptestcli -config "builtin://Recommended Rules" -input MyProject.vcproj

You can specify the build configuration and the platform you want to use during analysis of your project or solution. Append the configuration and platform names to the solution or project file name. Your command may resemble the following:

cpptestcli -config "builtin://Recommended Rules" -input MyProject.vcproj@Debug|x64

Alternatively, you can use the following properties to specify the build configuration and the platform you want to use during analysis of all Visual Studio solutions and projects:

cpptest.input.msvc.config=Debug
cpptest.input.msvc.platform=x64

For all Microsoft Visual Studio settings, see Visual Studio Settings.

Ensure that the correct version of Microsoft Visual C++ compiler is available on $PATH before running analysis. Microsoft Visual Studio 6 is not supported.

Specifying Test Data Location

Exclusive access to the .cpptest directory is required. The directory is created in the current working directory by default, which is where some of the run-specific data is stored. As a result, only one instance of C/C++test can run in a directory at a time. You can use the -workspace switch to change the location of the .cpptest directory.

-workspace <WORKSPACE_LOCATION>